Follow Us: iconfinder 5365678 fb facebook facebook logo icon 64px   iconfinder 5296765 camera instagram instagram logo icon 64px   iconfinder 5296516 tweet twitter twitter logo icon 64px   youtube 64px



Visit our Members Gallery to view the many fine pieces built by SAPFM members. Many are museum reproductions. We hope that among these many masterworks you will find inspiration for your next build.



Visit the Gallery




Phil Lowe

Woodworker and Friend



As most of us know PhiL Lowe was a longtime SAPFM member, 2005 Cartouche Award recipient, teacher to countless students, mentor and friend to many of us.

It is with great honor and privilege that the Board of Directors at SAPFM is announcing the support of preserving the Phil Lowe drawing library .

Visit the Library >>


American Period Furniture Throughout the Decades


Enjoy the Many Benefits of SAPFM Membership

Members enjoy the following benefits.

  • A subscription to our annual American Period Furniture Journal mailed each December
  • A subscription to our quarterly Pins & Tails e-magazine.
  • Participation in all local chapter events
  • Eligibility to attend SAPFM confrences and particapte in SAPFM exhibitions
  • Access to on-line resources including our library of articles, past issues of Pins & Tails e-magazine, and more
  • An online gallery where Members' work is displayed
  • Our online Members forum

See More >>

Mirka Hand Sanding System

BY BOB LANG April 1, 2021 Updated April 1, 2021

I can develop a pretty smooth surface with a hand plane and/or a scraper, but before finishing I sand to ensure that all the surfaces of a project are consistent. Each hand tool leaves a slightly different texture that won’t be apparent until a stain, dye or topcoat is applied. Sanding may not be romantic but it’s an essential step. Although I own a number of power tools for sanding, I sand by hand to achieve better results and to minimize the dust. But I don’t sand by hand the way I used to, I’ve found a better abrasive material and a modern device to hold it.  

Besides the dust the downside to power sanding the likelihood of swirl marks, and the tendency to degrade the flatness of surfaces and remove crisp edges. Those surfaces and edges are important to preserve in a nice piece of furniture and the easiest way to get rid of swirl marks is to not produce them. The Mirka Hand Sanding Block, used in conjunction with Abranet abrasive solves these issues. As shown, the block is 2-3/4” X 5” ( a longer block is also available) and it connects to my shop vac with a lightweight flexible hose. The surface of the block grips the back of the abrasive sheet like the familiar “hook and loop” fastener, but the interface remains firm. With conventional sandpaper the “hook and loop” system introduces a flexible layer between the block and the abrasive. The Mirka block, as well as Mirka’s power sanders, leaves flat surfaces flat and corners nice and crisp.

PNT 0321 Mirka 9880

The abrasive itself is a fine mesh coated with abrasive particles. You can find technical details on the Mirka website The advantage of the mesh over a standard sheet of sandpaper is that sanding dust isn’t trapped on the surface of the wood, it moves through the net. With a vacuum attached to the block the dust is removed, but Abranet is also effective when sanding at the lathe, or sanding curved surfaces by hand. When I sand moldings I back up the abrasive with an old Skotchbrite pad to help it conform to the curved surfaces. Abranet doesn’t clog up and it doesn’t shed particles the way conventional sandpaper can. While the initial cost is higher, Abranet lasts significantly longer than traditional sandpaper. It also seems to remove material more efficiently than sandpaper, so I start sanding with a finer grit than I would normally use.

PNT 0321 Mirka 9884

The block fits comfortably in my hand and holes in the bottom allow air to move through the mesh to the shop vac. There is a valve at the connection of the hose and the block that controls the flow of air. With a powerful shop vac, it can be hard to push the block at full air flow. At the other end of the hose is a flexible cone shaped connector that pushes into the inlet of the shop vac. Abranet is available in pre-cut sheets and on rolls. Discs are also available for most random orbit sanders, as are adapters to replace the standard backing disc if needed.

Since I purchased my block a few years ago, the manufacturer has changed the color from black to yellow. The block and hose can be hard to find as most retailers would rather sell you a new powered sander, but here is an online source: The block and the hose are sold separately, at about $30-35 each. Rolls of abrasive are also about $30 each. I regularly use #120, #180 and #240, so my total cost was around $150. Coarser and finer grits are also available, but these three meet my needs. Pre-cut sheets are also available, but the rolls give me more flexibility if I need a small piece at an odd size. Sanding is still a chore, but this system makes it more pleasant, more efficient and it keeps me from working in a cloud of dust.

Editors Note: This article first appeared in the SAPFM Pins and Tails Magazine, Spring 2021

Upcoming Events


New Articles

  • Fitting an Asymmetrical Splat Into an Oval Chair Back

    BY DAVE HELLER April 1, 2021 Updated: April 1, 2021 This article discusses a specific aspect of making a set of not-yet-completed Bing-style Art Nouveau dining room chairs of my own design. I will write an article for SAPFM on...

  • A Standup Davenport Computer Desk

     BY JOE PARKER April 1, 2021 Updated: April 1, 2021 The name "Davenport" comes from a reference in the records of an 18th-19th century English furniture maker Gillows. The reference, in about 1795, gives the original design and...

  • Remembering Phil Lowe: Craftsman, Mentor, Friend

    BY MICKEY CALLAHAN April 1, 2021 Updated April 1, 2021 It’s with a heavy heart that I write of the passing of one of America’s master period furniture makers, Phil Lowe. I’ve known Phil for over 30 years and was privileged to have...

  • Luthier's Friend To Thickness Small Part

    BY JEFF THOMPSON April 1, 2021 Updated April 1, 2021 There are number of ways one can thickness stringing and bindings. I’ve used a couple methods myself like on a drum sander, but mine is in a shed out back behind my shop...

  • Mirka Hand Sanding System

    BY BOB LANG April 1, 2021 Updated April 1, 2021 I can develop a pretty smooth surface with a hand plane and/or a scraper, but before finishing I sand to ensure that all the surfaces of a project are consistent. Each hand...

Cartouche Award

  1. The Award
  2. Guidelines
  3. Cartouche Recipients


  1. SAPFM Business Member Directory
  2. Our Sponsors


  1. American Period Furniture
  2. Pins & Tales Magazine